LD端面泵浦Cr4:YAG被动调Q激光器输出特性研究

对激光二极管端面泵浦Cr⁴⁺:YAG被动调QNd:YAG激光器输出特性进行了实验研究.实验研究发现,激光器输出功率及脉冲重复频率随谐振腔长度增大而增大.为解释这一实验现象,测量了泵浦光斑在激光晶体内尺寸,同时计算了激光晶体及Cr⁴⁺:YAG晶体内的基模激光光斑半径随谐振腔长度变化.分析结果表明:激光晶体内泵浦光斑尺寸远小于激光晶体内基模光斑半径,腔模间交叠效率较低;当腔长增加时,激光晶体内的基模激光光斑减小,腔模间交叠效率增加,从而导致输出功率及脉冲重复频率随腔长增加而增加;另外,Cr⁴⁺:YAG晶体内光斑半径也随谐振腔长度减小,引起Cr⁴⁺:YAG晶体漂白时间缩短,导致脉冲重复频率随腔长增加而增加.     

Optimization of passively Q-switched laser with V:YAG saturable absorber

By considering the Gaussian spatial distributions of the intracavity photon density and the initial population-inversion density, the coupled rate equations for a diode-pumped passively Q-switched laser with V³⁺:YAG saturable absorber are given. These coupled rate equations are solved numerically and the key parameters of an optimally coupled passively Q-switched laser with V³⁺:YAG at 1342 nm are determined. These key parameters include the parameters of the gain medium, the saturable absorber and the resonator, which can maximize the pulse energy of singly Q-switched pulse. The optimal calculations for a diode-pumped passively Q-switched a-Nd:GdVO₄ laser with V³⁺:YAG saturable absorber are presented to demonstrate the numerical simulation applicable.     

Investigation of cutting of engineering ceramics with Q-switched pulse CO2 laser

In this paper, the cutting of Si₃N₄ engineering ceramics with Q-switched pulse CO₂ laser is studied. Considering the influence of the cut front shape on the absorption of the laser beam, a simplified 2D mathematic model is developed based on a pulsed laser vaporization cut process. This model is based on the conservation of energy. The experimental results show that it would realize crack-free cutting by using high-speed and multi-pass feed cutting process.     

调Q钕玻璃激光器宽频带倍频

本文描述了宽频带激光非线性相互作用耦合方程,并在Δλ(FWHM)=60的钕玻璃调Q激光系统上对不同类型倍频器进行宽频带倍频的实验研究。实验结果与理论计算符合得很好。     

Studies on Nd∶YAG Single-pass Amplifiers for High-power Q-switched Laser System

The output of Nd∶YAG single-pass laser amplifiers is studied analytically and experimentally. Methods of analysis for single-pass Nd∶YAG laser amplifier are presented. A flashlamp-pumped Q-switched Nd∶YAG oscillator/amplifier laser system has been developed with the average output power of 121.5 W.     

二极管泵浦的被动调Q与脉冲幅度混沌Nd:LaMgAl11O19全固态激光器

基于二极管泵浦Nd:LaMgAl₁₁O₁₉无序晶体激光器实现了被动调Q激光以及脉冲幅度混沌激光的输出。当泵浦功率在4.8~8.6 W范围内时,激光器运转在被动调Q状态;当泵浦功率为8.6 W时,调Q激光的平均输出功率为613 mW、重复频率为157.1 kHz、脉冲宽度为2.2μs。当泵浦功率增加到8.7~10.5 W范围内时,输出激光的脉冲幅度呈不规则随机分布现象;通过分析脉冲峰值序列的自相关曲线、相位图、功率谱、随机直方图,判定激光器运转在脉冲幅度混沌状态;当泵浦功率功率为10.5 W时,脉冲幅度混沌激光的平均输出功率为814 mW。     

离子注入SI—GaAs做激光器被动调Q元件的研究

本文从半导体材料GaAs的能级结构出发，探讨了GaAs做固体激光器被动调Q器件的可行性，对离子注入半绝缘GaAs用做Nd：YAG激光器中被动调Q元件的机理进行了实验研究，实验中腔型选择直腔式平平腔，Nd：YAG采用脉冲氙灯抽运，在腔型1Hz下获得了单脉冲宽度为62ns的调Q波形输出。     

The study of green laser performances by using composite crystals of different initial transmissions

This paper reported a passively Q-switched green laser of LD pumped linear cavity structure by using Nd:YAG/Cr⁴⁺:YAG composite crystal and the type II phase matching KTP crystal. The dependence of average output power, pulse width and pulse repetition rate on pump power at different initial transmissions of Cr⁴⁺:YAG were measured and analyzed. With Cr⁴⁺:YAG of 80% initial transmission, under pump power of 13.97 W, the output average power is up to 681 mW, with pulse width of 200 ns and pulse repetition rate of 9.1 kHz. The laser operates in a fundamental mode.     

环形腔被动锁模掺饵光纤激光器

通过在非线性偏振旋转环形腔内引入一种可旋转的在线起偏器,在保证装置的全光纤化结构的前提下,简化了被动锁模光纤激光器的结构.通过联合调节可旋转的在线起偏器、1/2波片和1/4波片的角度实现了掺饵光纤锁模脉冲20nm间隔的双波长调谐输出,调谐过程中观察到了锁模脉冲双波长状态.另外,从装置中去掉1/2波片后,仅调谐可旋转的在线起偏器和1/4波片也能够实现锁模脉冲的单波长稳定输出.     

LD端面泵浦Cr~4∶YAG被动调Q激光器输出特性研究

对激光二极管端面泵浦Cr4+∶YAG被动调Q Nd∶YAG激光器输出特性进行了实验研究.实验研究发现,激光器输出功率及脉冲重复频率随谐振腔长度增大而增大.为解释这一实验现象,测量了泵浦光斑在激光晶体内尺寸,同时计算了激光晶体及Cr4+∶YAG晶体内的基模激光光斑半径随谐振腔长度变化.分析结果表明:激光晶体内泵浦光斑尺寸远小于激光晶体内基模光斑半径,腔模间交叠效率较低;当腔长增加时,激光晶体内的基模激光光斑减小,腔模间交叠效率增加,从而导致输出功率及脉冲重复频率随腔长增加而增加;另外,Cr4+∶YAG晶体内光斑半径也随谐振腔长度减小,引起Cr4+∶YAG晶体漂白时间缩短,导致脉冲重复频率随腔长增加而增加.